MAINI Quickwedge Scaffolding
Quickwedge Standards / Verticals form the support and are made from Standard Scaffold Tubes of 48.3 x 4 mm thick. With the latest innovations, they are also available in 48.3 x 3.25mm in both grade 50 & 40 C as per BS: 4360. They have a series of “V” pressed welded at nominal 500 mm on the tube to provide a location for ledger and transoms. They are also available with integral wedge spigots or as open ended.
Quickwedge Standard
| Sizes | |
| 9 ft 9 ins (3m) | 6ft 6 ins (2m) |
| 4ft 10.5 ins (1.5m) | 3ft 3 ins (1m) |
Quickwedge Standards / Verticals form the support and are made from Standard Scaffold Tubes of 48.3 x 4 mm thick. With the latest innovations, they are also available in 48.3 x 3.25mm in both grade 50 & 40 C as per BS: 4360. They have a series of “V” pressed welded at nominal 500 mm on the tube to provide a location for ledger and transoms. They are also available with integral wedge spigots or as open ended.
Quickwedge Ledger
| Sizes | |
| 8 ft 0 ins (2.4m) | 6ft 0 ins (1.8m) |
| 4ft 2 ins (1.2m) | |
These items are made from tube with pressed wedge-fixing device at each ends. These are used to Tie the standards longitudinally. On the inside of the scaffold they are used at platform level and on the outside as a guardrail.
Quickwedge Transom
| Sizes | |
| 6ft 0 ins (1.8m) | 4ft 2 ins (1.2m) |
| 2ft 8 ins (0.8m) | |
These are made out of 50 x 50 x 5/4mm Angle, joined back to back with Flange Type extensions on both sides which provides support for working platforms with Battens. These are engaged with “V” pressing on the standards.
Quickwedge Return Transom
| Sizes | |
| 8 ft 0 inches (2.4m) | 6ft 0 inches (1.8m) |
| 4ft 2 inches (1.2m) | |
Manufactured from steel pressing shaped so that it can be placed over a ledger to form a 900 return in the scaffold, the Return Transom has a seating on one side for steelstage or Timber Battens.
Quickwedge Diagonal Brace
| Sizes | |
| 12 ft 0 inches (3.5m) | 9ft 0 inches (2.7m) |
Quickwedge Access Stage Bracket
| Item | |
| 3 Board | |
Cantiliver transom similar to the stage bracket with integral guard rail standard to take a ledger. This component is used where a platform is required on the outside of the scaffold with steel or timber battens makes a platform of 0.686m wide and available in both rolled section and back to back angles.
Quickwedge One Board Stage Bracket
One board stage bracket enables an additional 255 mm platform to be provided on the inside of the scaffold. They do not require Tie Bars to connect them together. Available with rolled “T” section or back to back welded angles.
Quickwedge Two Board or Three Board Stage Bracket
Two and Three Board Stage Brackets enable an additional 450mm (1’1”) and 675mm (2’3”) platform respectively to be provided on the inside of the scaffold nearest to the building. Tie Bars must be used to connect the brackets together. They are available in both rolled section and back to back welded angles.
Quickwedge Steel Batten
Steel Battens are light wight non-slip working surface which can be used with Transoms.
Tie Bar
Made out of 38mm x 38mm angle iron with a dowl at both ends. Used to connect stage brackets together.
Toe Board Bracket
When clamped to standards at the end of the scaffold platform, the Toe Board Bracket secures the End Toe Board, which can be either Steelstage or timber